ICL8038-Green - ICL8038 DDS jelgenerátor modul Sine Square háromszög hullám kimenet DC12V-25V

A cím elején szereplő szín/minta/méret/típus kerül kiszállításra!
ICL8038 DDS Signal Generator Module Sine Square Triangle Wave Output DC12V-25V
DC 12V-25V ICL8038 DDS Signal Generator Module Sine Square Triangle Wave Output2PCS ICL8038 ICICL8038 ICL8038CCPD INTERSIL IC OSCILL GEN/VOLT CONTROL 14DIP NEW D6ICL8038 - Yellow:
(1) output triangular wave, square wave and sine wave.
(2) frequency range: 10HZ ~ 300kHz
(3) Duty range: 2% to 98%
(4) Low-distortion sine wave: 1%
(5) low temperature drift: 50ppm / ℃
(6) of the triangular wave output linearity: 0.1%
(7) Power supply: 12V ~ 24V
Package included:1 x DC 12V-24V ICL8038 DDS Signal Generator Module Sine Square Triangle WaveICL8038 Kits:
Notice
Requires a certain DIY ability, you need to weld the kit yourself）
ICL8038 pin functions:
1 foot, 12 foot: sine waveform adjusting terminal;
2 foot: sine wave output;
3 foot: triangle wave output;
4 foot, 5 foot: the frequency and duty cycle (or waveform asymmetry) adjustment;
6 foot: V , the positive power supply;
7 foot: offset; 8 foot: frequency adjustment input terminal;
9 foot: square wave output.
This is an open collector output terminal, work should take a load resistor to the corresponding positive power supply terminal from the pin, to get a TTL-compatible square-wave output, the load resistance must be connected to 5V power supply;
10 foot: timing capacitor terminal;
11 foot: V-, negative power supply terminal or the ground. Use positive and negative power supply, 11 feet to the negative supply, the output waveform are symmetrical with respect to 0V; use a single positive power supply, 11 feet grounded, the output waveform is unipolar, uniform voltage is VCC / 2;
13 feet, 14 Feet: Empty foot.
The kits are designed for a frequency range is 50-5KHz, two bands with a switch S to switch, RP1 is the frequency adjustment, RP2 is the duty cycle adjustment, RP3 is a sine wave distortion adjustment. Circuit uses 12V single power supply, input from the X1; X2, X3 is a waveform output side, you can use oscilloscope to observe three output waveforms.
Model: ICL8038
Input: 12V DC
Frequency range 50-5KHz,
Size:6cm*4.5cm*0.2cm
Package Included:1 set function signal generator module and electronic kit ICL8038 - Green:NoticeIt is an welded product.
Model: ICL8038
Input 12V DC
Frequency range 50-5KHz,
Size:6cm*4.5cm*0.2cmPackage included: 1x ICL8038 Monolithic Function Signal Generator Module Sine Square Triangle ICL8038 Low-frequency:

1. Module size:50x50mm
2. Module working voltage:±5V-±12V DC
3. Low Frequency Drift with Temperature : 50ppm/oC
4. Low Distortion Sine Wave:011%
5. Triangle Wave Output Linearity : 011%
6. Wide Frequency Range : 01001Hz to 300kHz
7. Duty Ratio Range : 2% to 98%
8. Simultaneous outputs an arbitrary Sine, Square, and Triangle Wave
Package included:1 x Low-frequency Signal Source Generator ModuleICL8038 Kits Shell
Using ICL8038 high-speed op amp composed of signal generator, by the following characteristics
(1) can output triangular wave, rectangular wave and sine wave, forward and reverse sawtooth wave.
(2) frequency adjustment range: 5HZ ~ 400kHz
(3) duty cycle adjustment range: 2% to 95%
(4) low distortion sine wave: 1%
(5) Low temperature drift: 50ppm / ℃
(6) triangular wave output linearity: 0.1%
(7) single power supply (built-in power management IC): 12 V ~ 15 V
(8) DC bias adjustable: -7.5V-7.5V
(9) Output amplitude adjustable: 0.1V-11VPP (operating voltage 12V)DIy kits with Transparent ShellPackage Include: 1 x DIY DC 12V ICL8038 5HZ~400KHZ Function Signal Generator Sine Triangle Sawtooth Shell
ICL8038-Blue
Features:
Working voltage: 12V ~ 15V
Output: Triangular wave, Square wave and sine wave.
Frequency range: 10HZ ~ 450kHz
Low distortion sine wave: 1%
Duty cycle range: 2% to 98%
Low temperature drift: 50ppm / ℃
Triangular wave output linearity: 0.1%
Working temperature: 0 ~ 70 ℃
Board size: 54.5*37.8mmFunctions:
VCC,GND: working voltage
AC: with DC bias output
G: ground
DC: pure signal output
R11: Frequency adjustment
R12: Square wave duty cycle adjustment
R13: Sine wave linear adjustment
R14: Amplitude adjustment
R15: Square wave linear adjustment
Jumper P2: select different waveforms(triangular, square or sine waves)
Jumper P3: select different frequency ranges
10Hz-450Hz
90Hz-1.5KHz
940Hz-15KHz
6KHz-120KHz
20KHz-450KHzPackage Include: 1 x ICL8038 Low/Medium Frequency Signal Source Waveform Signal Generator Sine Wave
311995517354/3 - ali110 (280)