Szín: NO RX DJI RC-hez - Új iFlight Alpha A85 HD Whoop BNF Polar Nano Vista digitális HD rendszerrel/SucceX-D 20A F4 Whoop

Let's welcome the iFlight Alpha series, a new way to fly
FPV. Ever wanted to try Digital FPV on the smallest possible whoop size quad? We
sticked the caddx Vista and the new polar nano to one of our new 2inch whoop
frames, did some tuning and tried to find the optimal ratio between weight and
power. This is what we came up with to combine flight time efficiency with
sufficient power. 
Features：
84.5 grams (without
battery) 
Butter smooth XING1303
5000KV，more torque and efficiency with longer flight times compared to 1105
motors 
Ducts to protect the sensitive
environment or yourself
Pre-tuned with smooth cinematic
settings
iFlight Albatross5.8G light antenna upgrade
(included)
iFlight Albatross 900mhz light micro antenna upgrade (included with every
Crossfire Nano RX)
Alpha A85 HD BNF Specs:
SucceX-D 20A Whoop F4 AIO Board
XING 1303 5000KV FPV Micro
Motor
Wheelbase:
85mm
Body size:
125*125mm
Ducted propeller size: 2
inch
FC pattern:
25.5*25.5mm
FPV cam spacing:
14mm
Weight: 84.5g (without
battery)
Flight time: 5-7 min cruising
(4S 450mAh) 
PRE-TUNED & PRE-SETUP:
- Don't worry about tuning, we did that for you already!
A basic PID- and Filter tuning was applied for a great flight
experience!
To restore lost tunes or updates, please check our
linked article on "Firmware/Factory Dumps"
- Angle-Mode (self balancing level mode) is enabled by
default to make sure your first flight doesn't end in a mess!
Please check our linked article on "How to disable Angle-Mode, activate
Acro-Mode"
Alpha A85 HD Quad BNF Included Components and
Parts
Prebuilt and tested
Quadcopter
1x Alpha 85mm
Frame
1x Polar Nano Vista Digital HD
System Kit
1xAlbatross
LHCP ipex 5.8g light
antenna
2sets HQ 2 inch 4-blades (Set of
4 - Color May Vary)
1x iFlight Lipo
Strap
FC // SucceX-D 20A F4 Whoop
AIO (SKU:S009200)
*Size：30.5*30.5mm
*Mounting pattern：25.5*25.5mm/φ3mm
*Connector：Micro-USB
*MCU：STM32F411
*Gyro：MPU6000
*Blackbox：8MB
*BEC output：5V 2A/10V 2A
*INA pad：UART2 (nR2) 
*Barometer：no
*Constant current：20A，25A（Burst）
*Input：2-4S
*Current sensor：yes
*BLHeli：BLHeli-S
*ESC Telemetry：no
*Target：IFLIGHT_F411_PRO
*ESC Firmware：G-H-30 BLS
Additional Suggested Parts
DJI HD FPV
Goggles
Radio
Controller
Battery 4S
450mAh
Important
The DJI Remote Controller is
recommended for beginners since you won't need to set up another receiver, but
it is also optional in this BNF drone because it is NOT required in order to use
the FPV system. If you don't choose to use the DJI Remote Controller, you can
choose a receiver option for your transmitter and then bind to your own radio as
usual.
Our current frsky receivers
default version in 2.XX, requires to use the same version of frsky
transmitter. 
If you have none frsky
transmitter,please downgrade the version lower than 2.X.X, www.frsky-rc.com for
more details.
Note:
All iFlight BNFs are tested before shipment to guarantee
highest quality. 
If
you still encounter a problem after receiving your shipment, please immediately
contact our iFlight customer support at www.iflightrc.freshdesk.com.
iFlight takes no responsibility for issues with DJI or
Caddx 3rd party gear (Video transmitters, Goggles, Radios, etc) and must be
directly reported to www.caddxfpv.com/pages/contact-us or www.dji.com/support.