Kosár
0
Termék
Termék
(üres)
Nincs termék
To be determined
Szállítás
0 Ft
Összesen
Termék a kosaradba helyezve
Mennyiség
Összesen
0 termék a kosaradban.
1 termék a kosaradban.
Termék összesen
Szállítás összesen
To be determined
Összesen
ZVS generátor modul tok - ZVS Tesla DC tekercs Marx generátor 12-30V nagyfeszültségű tápegység modul tok
201988556079/3
Új termék
ZVS Tesla DC Coil Marx Generator 12-30V High Voltage Power Supply Module CaseDescription:ZVS Generator Module
100% Brand new and High quality
This is Assembled Board
Size: 74mm x 77.8mm
Input Voltage: DC 12V-30V
Power Requirement: Less than 12V≥5A, Above 15V≥15A
Operating Frequency: 30KHz-50KHz adaptive
Secondary Parameters: 5T 5T
About the length of the discharge arc: Input voltage 12V/5A, the high voltage discharge arc distance is about 1-2CM. The greater input voltage and current increases, the greater output power, the longer discharge arc distance, when input the maximum 30V/10A, distance can up to above 5CM. If the arc is too short, please check the input power is sufficient.
About Power: Power output circuit depends on your input power, if you only 30W power supply, even if you want to be a 200W ZVS, is can not up to the output of 100W or 200W, so the input power must be adequate, power = voltage x current !
Input Voltage/Current Output Voltage Max Power
12V/5A About 10000V 60W
24V/10A About 20000V 200W
Package Included:1 x Assembled ZVS Tesla Coil Driver BoardAcrylic Case For ZVS Generator Module
Shell for the transparent acrylic, shipping shell are spare parts, please pro note, because the assembled shell hollow, bad delivery, easy to crush.
Delivery of both sides of the physical have a layer of protective layer, after receipt of the goods before the installation of the protective layer to tear and then assembled.
Shell shipping list:
(1) transparent acrylic shell 1 set
(2) set of screws:
30MM double through copper pillars 4
M3 * 10 screws 9ZVS Generator Module Case
Package included:
1*Assembled ZVS Tesla Coil Driver Board
1*Acrylic Case (DIY Kits)ZVS Generator Black Board:
Features:
1. size: 74 mm * 77 mm
2. input voltage: 12V-30V recommended 24V
3. Power supply requirements: less than 15V≧ 5A; 15V or more≧15A
4. Operating frequency: 30KHZ - 60KHZ
5. Secondary parameters: 5T 5T
6. Use military 1.6mm double board, four fixed 3 mm hole.
7. Mixer tube to add new field with a 30mm large heat sink, greatly improve the stability and life!
8. Low density component placement, better heat dissipation, Especially the capacitance, the majority of ZVS plate will be 2 capacitance placed side by side!
9. Extra power line tin, current-carrying capacity more strong!
10. Metal film resistor power, high precision, small Temperature drift!Package Include: 1 x ZVS Tesla Flyback Driver Board Zero Voltage Switching F
100% Brand new and High quality
This is Assembled Board
Size: 74mm x 77.8mm
Input Voltage: DC 12V-30V
Power Requirement: Less than 12V≥5A, Above 15V≥15A
Operating Frequency: 30KHz-50KHz adaptive
Secondary Parameters: 5T 5T
About the length of the discharge arc: Input voltage 12V/5A, the high voltage discharge arc distance is about 1-2CM. The greater input voltage and current increases, the greater output power, the longer discharge arc distance, when input the maximum 30V/10A, distance can up to above 5CM. If the arc is too short, please check the input power is sufficient.
About Power: Power output circuit depends on your input power, if you only 30W power supply, even if you want to be a 200W ZVS, is can not up to the output of 100W or 200W, so the input power must be adequate, power = voltage x current !
Input Voltage/Current Output Voltage Max Power
12V/5A About 10000V 60W
24V/10A About 20000V 200W
Package Included:1 x Assembled ZVS Tesla Coil Driver BoardAcrylic Case For ZVS Generator Module
Shell for the transparent acrylic, shipping shell are spare parts, please pro note, because the assembled shell hollow, bad delivery, easy to crush.
Delivery of both sides of the physical have a layer of protective layer, after receipt of the goods before the installation of the protective layer to tear and then assembled.
Shell shipping list:
(1) transparent acrylic shell 1 set
(2) set of screws:
30MM double through copper pillars 4
M3 * 10 screws 9ZVS Generator Module Case
Package included:
1*Assembled ZVS Tesla Coil Driver Board
1*Acrylic Case (DIY Kits)ZVS Generator Black Board:
Features:
1. size: 74 mm * 77 mm
2. input voltage: 12V-30V recommended 24V
3. Power supply requirements: less than 15V≧ 5A; 15V or more≧15A
4. Operating frequency: 30KHZ - 60KHZ
5. Secondary parameters: 5T 5T
6. Use military 1.6mm double board, four fixed 3 mm hole.
7. Mixer tube to add new field with a 30mm large heat sink, greatly improve the stability and life!
8. Low density component placement, better heat dissipation, Especially the capacitance, the majority of ZVS plate will be 2 capacitance placed side by side!
9. Extra power line tin, current-carrying capacity more strong!
10. Metal film resistor power, high precision, small Temperature drift!Package Include: 1 x ZVS Tesla Flyback Driver Board Zero Voltage Switching F
Egyéb infó
A cím elején szereplő szín/minta/méret/típus kerül kiszállításra!
ZVS Tesla DC Coil Marx Generator 12-30V High Voltage Power Supply Module CaseDescription:ZVS Generator Module
100% Brand new and High quality
This is Assembled Board
Size: 74mm x 77.8mm
Input Voltage: DC 12V-30V
Power Requirement: Less than 12V≥5A, Above 15V≥15A
Operating Frequency: 30KHz-50KHz adaptive
Secondary Parameters: 5T 5T
About the length of the discharge arc: Input voltage 12V/5A, the high voltage discharge arc distance is about 1-2CM. The greater input voltage and current increases, the greater output power, the longer discharge arc distance, when input the maximum 30V/10A, distance can up to above 5CM. If the arc is too short, please check the input power is sufficient.
About Power: Power output circuit depends on your input power, if you only 30W power supply, even if you want to be a 200W ZVS, is can not up to the output of 100W or 200W, so the input power must be adequate, power = voltage x current !
Input Voltage/Current Output Voltage Max Power
12V/5A About 10000V 60W
24V/10A About 20000V 200W
Package Included:1 x Assembled ZVS Tesla Coil Driver BoardAcrylic Case For ZVS Generator Module
Shell for the transparent acrylic, shipping shell are spare parts, please pro note, because the assembled shell hollow, bad delivery, easy to crush.
Delivery of both sides of the physical have a layer of protective layer, after receipt of the goods before the installation of the protective layer to tear and then assembled.
Shell shipping list:
(1) transparent acrylic shell 1 set
(2) set of screws:
30MM double through copper pillars 4
M3 * 10 screws 9ZVS Generator Module Case
Package included:
1*Assembled ZVS Tesla Coil Driver Board
1*Acrylic Case (DIY Kits)ZVS Generator Black Board:
Features:
1. size: 74 mm * 77 mm
2. input voltage: 12V-30V recommended 24V
3. Power supply requirements: less than 15V≧ 5A; 15V or more≧15A
4. Operating frequency: 30KHZ - 60KHZ
5. Secondary parameters: 5T 5T
6. Use military 1.6mm double board, four fixed 3 mm hole.
7. Mixer tube to add new field with a 30mm large heat sink, greatly improve the stability and life!
8. Low density component placement, better heat dissipation, Especially the capacitance, the majority of ZVS plate will be 2 capacitance placed side by side!
9. Extra power line tin, current-carrying capacity more strong!
10. Metal film resistor power, high precision, small Temperature drift!Package Include: 1 x ZVS Tesla Flyback Driver Board Zero Voltage Switching F
201988556079/3 - ali110 (281)
ZVS Tesla DC Coil Marx Generator 12-30V High Voltage Power Supply Module CaseDescription:ZVS Generator Module
100% Brand new and High quality
This is Assembled Board
Size: 74mm x 77.8mm
Input Voltage: DC 12V-30V
Power Requirement: Less than 12V≥5A, Above 15V≥15A
Operating Frequency: 30KHz-50KHz adaptive
Secondary Parameters: 5T 5T
About the length of the discharge arc: Input voltage 12V/5A, the high voltage discharge arc distance is about 1-2CM. The greater input voltage and current increases, the greater output power, the longer discharge arc distance, when input the maximum 30V/10A, distance can up to above 5CM. If the arc is too short, please check the input power is sufficient.
About Power: Power output circuit depends on your input power, if you only 30W power supply, even if you want to be a 200W ZVS, is can not up to the output of 100W or 200W, so the input power must be adequate, power = voltage x current !
Input Voltage/Current Output Voltage Max Power
12V/5A About 10000V 60W
24V/10A About 20000V 200W
Package Included:1 x Assembled ZVS Tesla Coil Driver BoardAcrylic Case For ZVS Generator Module
Shell for the transparent acrylic, shipping shell are spare parts, please pro note, because the assembled shell hollow, bad delivery, easy to crush.
Delivery of both sides of the physical have a layer of protective layer, after receipt of the goods before the installation of the protective layer to tear and then assembled.
Shell shipping list:
(1) transparent acrylic shell 1 set
(2) set of screws:
30MM double through copper pillars 4
M3 * 10 screws 9ZVS Generator Module Case
Package included:
1*Assembled ZVS Tesla Coil Driver Board
1*Acrylic Case (DIY Kits)ZVS Generator Black Board:
Features:
1. size: 74 mm * 77 mm
2. input voltage: 12V-30V recommended 24V
3. Power supply requirements: less than 15V≧ 5A; 15V or more≧15A
4. Operating frequency: 30KHZ - 60KHZ
5. Secondary parameters: 5T 5T
6. Use military 1.6mm double board, four fixed 3 mm hole.
7. Mixer tube to add new field with a 30mm large heat sink, greatly improve the stability and life!
8. Low density component placement, better heat dissipation, Especially the capacitance, the majority of ZVS plate will be 2 capacitance placed side by side!
9. Extra power line tin, current-carrying capacity more strong!
10. Metal film resistor power, high precision, small Temperature drift!Package Include: 1 x ZVS Tesla Flyback Driver Board Zero Voltage Switching F
201988556079/3 - ali110 (281)
