Eredeti Uno R3 - Arduino UNO R3 WIFI ESP8266 ESP-12E ATmega328 CH340G WeMos D1 fejlesztési kártya

A cím elején szereplő szín/minta/méret/típus kerül kiszállításra!
Arduino UNO R3 WIFI ESP8266 ESP-12E ATmega328 CH340G WeMos D1 Development Board
UNO R3 WIFI ESP8266 ESP-12E ATmega328 CH340G WeMos D1 Development Board

Description:Original Arduino Uno R3 Microcontroller: ATmega328
Operating Voltage: 5V
Input Voltage (recommended): 7-12V
Input Voltage (limits) 6-20V
Digital I/O Pins 14 (of which 6 provide PWM output)
Analog Input Pins 6
DC Current per I/O Pin 40 mA
DC Current for 3.3V Pin 50 mA
Flash Memory 32 KB (ATmega328) of which 0.5 KB used by bootloader
SRAM 2 KB (ATmega328)
EEPROM 1 KB (ATmega328)
Clock Speed 16 MHz
Note: This is Original/Genuine Arduino Uno R3 Board!! Not a clone.
ESP-12E WeMos D1
Based on ESP-8266EX
Arduino compatible, using Arduino IDE to program
11 x I / O pins
1 x ADC pin (input range of 0-3.3V)
Support OTA wireless upload
Onboard 5V 1A Switching Power Supply (highest input voltage 24V)
After installing the hardware package,the direct use of Arduino IDE development, the same operation with Arduino UNOUNO WiFi R3 ATmega328PModel Number: UNO WiFi-R3-AT328-ESP8266-32MB-CH340G
is_customized: Yes
Brand Name: RobotDyn
Supply Voltage: 6~9V recommind
Type: Logic ICs
Condition: New
MCU: ATmega328
WiFi MCU: ESP8266
USB-converter: CH340G
PinOut Uno: Uno R3
UNO WiFi R3 ATmega328P ESP8266 (32Mb memory), USB-TTL CH340G. Compatible for Arduino Uno, NodeMCU, WeMos ESP8266
UNO R3 PLUSThe Uno R3 also adds SDA and SCL pins that are near to the AREF pin and two other new pins placed near to the RESET pin, the IOREF that allow the shields to adapt to the voltage provided from the board. In future, shields will be compatible both with the board that use the AVR, which operate with 5V and with the Arduino Due that operate with 3.3V. The second one is a not connected pin, that is reserved for future purposes.Besides,the board has stronger RESET circuit.
DM Strong Mini UNO R3 BoardThe UNO strong is an Arduino compatible board. It is based on Arduino UNO REV3 design. Some visible improvement on hardware make more flexible and easier to use. SPI, COM and IIC bus breakout make bus connect easier. The UNO strong is a microcontroller board based on the ATmega328. It has 14 digital input / output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or battery to get started.
Select "Arduino/Genuino Uno from the Tools > Board menu (according to the microcontroller on your board). For details, see the reference and tutorials. The ATmega328 on the Arduino Uno comes preprogrammed with a bootloader that allows you to upload new code to it without the use of an external hardware programmer. It communicates using the original STK500 protocol . You can also bypass the bootloader and program the microcontroller through the ICSP (In-Circuit Serial Programming) header using Arduino ISP or similar; see these instructions for details. The ATmega16U2 firmware source code is available in the Arduino repository. The ATmega16U2 is loaded with a DFU bootloader, You can then use Atmel's FLIP software (Windows) or the DFU programmer (Mac OS X and Linux) to load a new firmware. Or you can use the ISP header with an external programmer (overwriting the DFU bootloader).
The UNO strong has an increased pin header spacing of 2.54mm and leads to all I / Os and VCC / GND. We can conveniently connect various modules via DuPont wire, and our engineers love to use it for some applications.
UNO R3 BoardOpen circuit diagram of the original design, the development of software interface for free download, can also be in accordance with the requirements and their modified, download the program is simple and convenient. Can simply use sensors, all kinds of electronic components connection (such as: LED lights, buzzer, buttons, photoresistance, etc.), make all sorts of interesting work.Microprocessor controller, using high-speed development interface and the environment are very simple and easy to understand, very suitable for beginners to learn.
Performance Description
Digital I/O Digital inputs/outputs were0~13.
Analog I/O Analog input/output: 0~5
Support ISP download function.
The input voltage: when connected to the computer USB without external power supply,
external power supply 7 v to 12 v dc input voltage.
Output voltage: 3.3 V and 5 V dc voltage output dc voltage output.
ESP8266 ESP-13 UNO R3DC: 3.3-5V
ESPduino is developed by Doit company based on the ESP8266 ESP-13, which can be compatible with Arduino UNO R3 developmen board.
By using the ESP8266 WiFi and MCU,ESPduino supports WiFi. Compared to the traditional Arduino UNO development baord, users don't have to buy another WiFi development board.
UNO R3 ATmega328P CH340Main Changes from the older version:
Add two rows of the holes for the pins. So it can be connected with normal Dubond line.
Add 3 rows of the holes for wiring.
Change the in-line package of ATMEGA328P to flat package.
CH340G Replace ATmega16U2
Plug UNO development board, the driver will be automatically installed.
select the board UNO inside the die.
Select the COM port, this can be in my computer queries, just inside your uno port development board
You'd better to choose arduino own routine procedures, burn into the boar
UNO R3 CH340Add two rows of the holes for the pins. So it can be connected with normal Dubond line.
Add 3 rows of the holes for wiring.
Change the in-line package of ATMEGA328P to flat package.
CH340G Replace ATmega16U2
CH340 UNO Micro USBMain Changes from the old version:
1. Adding two rows of the holes for the pins, so it can be connected with normal Dupond lines.
2. Adding 3 rows of the holes for wiring.
3. ATmega16U2 is replaced by CH340G.
4. Plug and Play, the driver will be installed automatically.
5. Select the board UNO inside the DIE.
6. Interface: Common Micro USB interface, can use the phone charging cable, easy to us
Acrylic CaseWith screw copper pillar and installation instructions.
Weight: 53g
Dimensions: 79.5 x 64.5 x 21mm
Material: A grade acrylic sheet
For Arduino UNO R3 Development Board only
To protect your little computer against damages, dust and scratches Clear Top and Bottom.
This case provides easy access to all ports
It requires no tools for easy assembly and disassembly
Simply Clicks Together Enclosure
This case is a beautiful yet simple way to show off your Arduino UNO!
Arduino UNO R3 ABS Black CaseThese cases protect your Arduino Uno from things like rogue wires that might short it out while still allowing full access to the board! Simply snap the Uno into the bottom half of the enclosure, then snap the two sides together.
The enclosure provides slots to access each header, USB port, power jack, the reset button, the AREF and ICSP connectors, as well as feet and vents to ensure the board gets proper cooling and slide-in wall mounting slots. All of the status LEDs on the Uno are visible through the case thanks to light pipes embedded in the design.
Dimensions: 7.8 x 6.1 x 2.1cm
UNO R3 ABS Clear CaseWeight: 23 g
Volume: 7.5 x 6 x 2cm
Package Included:
1PC*ABS case for Arduino UNO R3(Clear)
1PC*Non-slip mat
4PCS*ScrewsUNO R3 ABS Black CaseWeight: 23 g
Volume: 7.5 x 6 x 2cm
Package Included:
1PC*ABS case for Arduino UNO R3(Black)
1PC*Non-slip mat
4PCS*Screws30CM Nano USB Cable100% Brand New.
USB 2.0 Male A to Mini B 5-pin cable.
Allows you to transfer images and data between your cell phone, MP3，PDA, GPS systems to computer.
Up to 480 Mbps data transfer rate.
Hot-swappable cable.
Plug and Play.
Cable Length: 30cm
Color: Blue
Blue USB Cable100% Brand New.
USB A Male to Type B Plug cable.
Connector Type: Standard USB jack
Wire: flexible PVC jacket, flexible and easy to break, durable
Advantages: with magnetic ring, anti-jamming performance
Product advantages:
1. Standard 2.0 connector provides excellent electrical conductivity, making high-speed transmission of data is fast and accurate interface with Baotou design, is conducive to Protect the USB interface, durable
2. Core all high-quality tinned oxygen-free copper, increase the signal transmission surface, anti-oxidation, life is higher than the average product 50 times
3. Wire with aluminum foil, braid double shield, anti-interference ability, signal transmission more stable
4. Using a unique signal line twisted way, increase the signal transmission stability
Product use:
printer cable is a USB male head, used to connect the computer's USB interface; the other end is the mouth of the mouth, for connecting USB printer
Micro USB Cable100% brand new and high quality
High Speed USB 2.0 Cable
Compatible with Cellphones, GPS systems, PDAs, OTG devices and digital cameras
Cable lenght: 30CM
Complies with fully rated cable specification using braid-and-foil shield protectionThis 30CM USB A to Micro USB B 5pin Cable provides one USB A Male connector, and one Micro USB B connector to create a simple way to connect mobile devices to a USB capable computer for every day tasks such as data synchronization and file transfers.The micro-USB connector is smaller and thinner than the previous USB Mini-b standard while offering better performance.Package Included:
1PC
312033437522/1 - ali110 (280)