CNC V2 pajzs - V2 / V3 / V4 CNC árnyékoló gravírozó 3D nyomtató bővítő kártya A4988 illesztőprogram

A cím elején szereplő szín/minta/méret/típus kerül kiszállításra!
V2/V3/V4 CNC Shield Engraver 3D Printer Expansion Board A4988 DriverCNC Shield V4 Expansion Board Set A4988 With USB CableFeatures:
100% Brand new and high quality!
This expansion board as a driver expansion board, can be used for engraving machines, 3D printers.
It is a total of four slots, can drive four A4988 stepper motor. Each road stepper motors only need two IO ports. In other words, six IO ports can be well managed three stepper motors. Very convenient to use.
UNO for Arduino module IO port correspondence introduction.
Best choice for yourself or your friend.You will not be disappointed!Specifications:
Color: Red
Type:cnc shield v4
Size: 7.2*5.9cmPackage included:
1 x CNC Shield V4 Expansion Board Suit
1 x USB Cable
CNC V4 ShieldSpecification3 axis stepper motor driver
Compatible with micro-drive laser engraving machine, three-axis CNC engraving machine,.
2A can be controlled within the two-phase four-wire stepper motor.
Released the digital IO interface, easy to connect to other modules, such as ENDSTOP.
Released the I2C interface, you can connect to the LCD I2C or other I2C module.
Power DC5V interface, 7.5-12V voltage input.
GRBL compatible
Worked with arduino nano.Package Included:1 x CNC Shield V4 Engraving Machine Stepper Motor Driver GRBL CompatibleCNC V2.0 shield
1.The new MKS Base 1.2 3D Printer Controller board combines and improves the assets of the RAMPS 1.4 and Arduino Mega 2560 boards on a fantastic single board solution. The MKS Base 1.2 is an optimal 3D printer controller solution for your Reprap 3D Printer.2. LCD 12864 Smart ControllerIt contains a SD-Card reader. You can easy connect it to your Ramps board using the ""smart adapter"" included. After connecting this panel to your Ramps you don't need your pc any more, the Smart Controller supplies power for your SD card.3.The DRV8825 stepper motor driver carrier is a breakout board for TI’s DRV8825 microstepping bipolar stepper motor driver. The module has a pinout and interface that are nearly identical to those of our A4988 stepper motor driver board, so it can be used as a higher-performance drop-in replacement for those boards in many applications. The DRV8825 features adjustable current limiting, overcurrent and overtemperature protection, and six microstep resolutions (down to 1/32-step). It operates from 8.2 – 45 V and can deliver up to approximately 1.5 A per phase without a heat sink or forced air flow (rated for up to 2.2 A per coil with sufficient additional cooling).Package Included:1PCS*CNC Shield A4988 Driver Expansion Board V2 nEgraevr 3D PrinterCNC V3.0 shield
Description:
100% brand new and high quality
This expansion board as a driver expansion board, can be used for engraving machines, 3D printers.
It is a total of four slots, can drive four A4988 stepper motor. Each road stepper motors only need two IO ports. In other words, six IO ports can be well managed three stepper motors. Very convenient to use.
UNO for Arduino module IO port correspondence introduction.
IO corresponding figure aboveUNO for Arduino---------------------- expansion board
8 ------------------------ EN ( stepper motor driver enable , active low )
7 ----------------------- Z.DIR (Z -axis direction control )
6 ----------------------- Y.DIR (Y -axis direction control )
5 ----------------------- X.DIR (X -axis direction control )
4 ---------------------- Z.STEP (Z -axis stepper control )
3 ---------------------- Y.STEP (Y -axis stepper control )
2 ---------------------- X.STEP (X -axis stepper control )/ / The following is a simple stepper motor control procedures,# define EN 8 / / stepper motor enable , active low
# define X_DIR 5 / / X -axis stepper motor direction control
# define Y_DIR 6 / / y -axis stepper motor direction control
# define Z_DIR 7 / / z axis stepper motor direction control
# define X_STP 2 / / x -axis stepper control
# define Y_STP 3 / / y -axis stepper control
# define Z_STP 4 / / z -axis stepper control
/ *
/ / Function : step . function: to control the direction of the stepper motor , the number of steps .
/ / Parameters : dir direction control , dirPin corresponding stepper motor DIR pin , stepperPin corresponding stepper motor " step " pin , Step number of step of no return value.* /
void step (boolean dir, byte dirPin, byte stepperPin, int steps)
{
digitalWrite (dirPin, dir);
delay (50);
for (int i = 0; i digitalWrite (stepperPin, HIGH);
delayMicroseconds (800);
digitalWrite (stepperPin, LOW);
delayMicroseconds (800);
}
}
void setup () {/ / The stepper motor used in the IO pin is set to output
pinMode (X_DIR, OUTPUT); pinMode (X_STP, OUTPUT);
pinMode (Y_DIR, OUTPUT); pinMode (Y_STP, OUTPUT);
pinMode (Z_DIR, OUTPUT); pinMode (Z_STP, OUTPUT);
pinMode (EN, OUTPUT);
digitalWrite (EN, LOW);
}
void loop () {
step (false, X_DIR, X_STP, 200); / / X axis motor reverse 1 ring, the 200 step is a circle.
step (false, Y_DIR, Y_STP, 200); / / y axis motor reverse 1 ring, the 200 step is a circle.
step (false, Z_DIR, Z_STP, 200); / / z axis motor reverse 1 ring, the 200 step is a circle.
delay (1000);
step (true, X_DIR, X_STP, 200); / / X axis motor forward 1 laps, the 200 step is a circle.
step (true, Y_DIR, Y_STP, 200); / / y axis motor forward 1 laps, the 200 step is a circle.
step (true, Z_DIR, Z_STP, 200); / / z axis motor forward 1 laps, the 200 step is a circle.
delay (1000);
}Note: When inserting the A4988 module, must be careful not to insert opposite. Stepper motor wiring as follows:
2A, 2B is a group (red, green), 1A, 1B is a group (blue, yellow), if want to change direction, can be change the position of one group , for example 2A, 2B mutually exchanged.Package Included:

1 x V3 Engraver 3D Printer New CNC Shield Expansion Board A4988 Driver
CNC Shield V3 Expansion Board SuitUNO R3 CNC Shield V3 Expansion Board 4pcs A4988Package included:

- 1x UNO R3 CH340 (with cable)
- 1x CNC Shield- 4x Stepper Driver A4988 inkl. Kühlkörper & Pad
Depends on your chioce!
401260947119/3 - ali110 (280)