> >>ZVS 12V-48V 40A nagyfrekvenciás indukciós fűtőmodul csap nélkül 1800W H1P1
Alacsonyabb ár! ZVS 12V-48V 40A nagyfrekvenciás indukciós fűtőmodul csap nélkül 1800W H1P1 Nagyobb
Előző Következő

ZVS 12V-48V 40A nagyfrekvenciás indukciós fűtőmodul csap nélkül 1800W H1P1

283453761620

Új termék

ZVS 12V-48V 40A High Frequency Induction Heating Module Without Tap 1800W H1P1

Adopted super PCB layout design and super heat sink, heat dissipation good, since with a cooling fan interface, can also do Tesla discharge, generator voltage inverter, etc..In this test, the maximum power is close to 1600W, and the maximum current is 35A. This product is available at under the condition of good heat dissipation, the utility model can work continuously for hours.
This induction heating circuit uses 12-48V low voltage DC power supply, maximum current 40A, the most highest power is 1800W. It can work continuously under the condition of good heat dissipation. Due to its moderate power, it can be used by DIY players to give smaller players the parts can be treated by quenching, annealing and other heat treatment. You can also be melted with graphite crucible Kim, Silver, Copper, aluminum and other metal, heating evenly, is fast and very convenient.
Note: 1. The power of heating is very large, except that the plate and components are hot, and the heat of copper tube is very high. The buyer can prepare water cooling system separately, can buy a small water pump and 2 meters of inner diameter of 4mm rubber hose. 2.When heating the metal objects do not to heat too large metal, otherwise it may be overloaded with power, please add a 35A fuse or ammeter and air switch will be better.
3. You must pay attention to when using switch power supply, because the high-power switching power supply usually have soft start function, namely the output voltage is slowly rising, and if the voltage rise to 10V before connected induction heating circuit will be caused by lacking voltage lead, so that the two MOS tube conduction and burned components at the same time, so be sure to switch the power supply voltage stability and then access the induction heating circuit.
4. The minimum input voltage of the module is 12V, it doesn`t mean all the 12V power supply can be used, some novice buyers may use a smaller power supply. This module has specific voltage

Bővebb leírás

-4 / 6 / Gyorsan Fogyó termék

8 865 Ft‎

-58%

21 106 Ft‎

Hozzáadás a kívánságlistához

Egyéb infó

ZVS 12V-48V 40A High Frequency Induction Heating Module Without Tap 1800W H1P1

Adopted super PCB layout design and super heat sink, heat dissipation good, since with a cooling fan interface, can also do Tesla discharge, generator voltage inverter, etc..In this test, the maximum power is close to 1600W, and the maximum current is 35A. This product is available at under the condition of good heat dissipation, the utility model can work continuously for hours.
This induction heating circuit uses 12-48V low voltage DC power supply, maximum current 40A, the most highest power is 1800W. It can work continuously under the condition of good heat dissipation. Due to its moderate power, it can be used by DIY players to give smaller players the parts can be treated by quenching, annealing and other heat treatment. You can also be melted with graphite crucible Kim, Silver, Copper, aluminum and other metal, heating evenly, is fast and very convenient.
Note: 1. The power of heating is very large, except that the plate and components are hot, and the heat of copper tube is very high. The buyer can prepare water cooling system separately, can buy a small water pump and 2 meters of inner diameter of 4mm rubber hose. 2.When heating the metal objects do not to heat too large metal, otherwise it may be overloaded with power, please add a 35A fuse or ammeter and air switch will be better.
3. You must pay attention to when using switch power supply, because the high-power switching power supply usually have soft start function, namely the output voltage is slowly rising, and if the voltage rise to 10V before connected induction heating circuit will be caused by lacking voltage lead, so that the two MOS tube conduction and burned components at the same time, so be sure to switch the power supply voltage stability and then access the induction heating circuit.
4. The minimum input voltage of the module is 12V, it doesn`t mean all the 12V power supply can be used, some novice buyers may use a smaller power supply. This module has specific voltage

283453761620 - bestbuy (214)

30 egyéb termék a kategóriából: