Features:Brand New & High...
Brand new and high qualitymeter: 28mmStep angle: 5.625 x 1 / 64Reduction ratio: 1 / 645 Line 4 phase can be driven by ordinary uln2003 chip can also be connected in phase 2development board used for.supporting the use of a direct plug and easy to use stepper motor used in the development board.Stepper motor driver board with ULN2003A, B, C, D four-phase...
130 DC motor,Miniature motor the mainshaft gear and propellerFeatures: length:25mmdiameter:21mmdiameter of axle:2mmaxiallength:9mmvoltage:3-6VBodysize: 25* 15* 20mmaxial length of motor:9mm, Rated Voltage:3vreference current :0.35-0.4ATest:3vrotate speed: 8000 R/MPackage Included : 10 x R130 motor Type 130 Hobby micro motors...
100% brand new and high quality.˘Control the speed of a DC motor with this controller.Control the light of a lamp with this controller.High efficiency, high torque, high power, high heat dissipation.With overcurrent protection.The high quality COMBICON improve the stability of circuit.Specifications: Input voltage: DC12V - 36VSustained...
Motor diameter:6mm0.8mmOutput shaft length:4.0mmVoltage:3.7VCurrent:0.12A(bring a small propeller speed)No-load current:0.04A(0.95A stall or so)Speed:46500rpmCable length:45mm about Package Included : 10 x 3.7V Hobby Motor Type 614 Micro Motor DC Hollow Motor 10PCS 3.7V Hobby Motor Type 614 Micro Motor DC Hollow Motor
Name:545 motorr />Specification:36*51mmwork voltage:12VPackage Included : 1 x DC Hobby Motor Type 545 Gear motor Toy Motor High Speed DC Hobby Motor Type 545 Gear motor Toy Motor High Speed
Specification:tor driver, compatible with anything that can output a digital 0 to 5V pulse (or 0 to 3.3V pulse if you solder SJ2 closed on the EasyDriver). EasyDriver requires a 7V to 30V supply to power the motor and can power any voltage of stepper motor. The EasyDriver has an on board voltage regulator for the digital interface that can be set to 5V or...
HomeerChips2PCS Micro Speed Reduction Gear Motor with Metal Gearbox Wheel DC 6V 30RPM N20Specification:Brand new & high quality Voltage: 6V Material: Metal Model: N20 Revolving Speed: 30RPM Total Length: 36mm Motor Size: 12mm(diameter)*26mm(height) Shaft Size: 3mm(diameter)*10mm(length) Package Included: 2 X Micro Speed Reduction Gear Motor with...
Brand new and high qualityameter: 28mmStep angle: 5.625 x 1 / 64Reduction ratio: 1 / 645 Line 4 phase can be driven by ordinary uln2003 chip can also be connected in phase 2development board used for.supporting the use of a direct plug and easy to use stepper motor used in the development board.Stepper motor driver board with ULN2003A, B, C, D four-phase...
The use chip: original A4988 chipintroductionA4988 is a complete microstepping motor driver with built-in translator for easy operation. The product can be full, half, 1/4, 1/8 and 1/16 step mode to operate bipolar stepper motor output drive capacity of up to 35 V and ± 2 A. A4988 includes a fixed off-time current regulator, the regulator can slow or...
Features: we quickly realized what an excellent add-on this would be. Using only two pins, control 16 free-running PWM outputs! I2C input, control 16 PWM output, you can control the 16 way servo motor.Specifications:Frequency: 40-1000Hz.Channel number: 16 channel.Resolution: 12 bit.Voltage: DC 5-10VSize: 60*25mmColor: blueNet Weight: 12 gPackage...
100% brand new and high qualitye speed of a DC motor with this controller.High efficiency, high torque, low heat generating.With reverse polarity protection, high current protection.SpecificationModel: CCMHCWorking Voltage: DC 12V - DC 40V.Control Power:0.01 - 400W.Current: Rated 8A, Max 10A.Static Current:0.02 A ( Standby ).PWM Duty Cycle:10% -100%.PWM...
motor drive module is ideal for use in battery-powered smart car, toy cars, robots. Supply voltage 2V ~ 10V, can drive two DC motors or a 4-wire 2-phase stepper motors ,can achieve forward rotation or reverse rotation, it is possible to adjust the rotation speed. Each can provide continuous current of 1.5A, peak current up to 2.5A, thermal protection and...
RF/VHF/UHF Transistor MOTOROLA TO-220 MRF477 MRF 477100% Genuine77 MRF 477100% Genuine77 MRF 477100% GenuinePackage Included:5 x RF/VHF/UHF Transistor MOTOROLA TO-220 MRF477 MRF 477100% Genuine 5PCS RF/VHF/UHF Transistor MOTOROLA TO-220 MRF477 MRF 477100% Genuine
New L293D motor shield, the input voltage DC4.5-25VDC4.5-25VDC4.5-25V600mA OUTPUT CURRENT CAPABILITY PER CHANNEL1.2A PEAK OUTPUT CURRENT (non repetitive)PER CHANNELENABLE FACILITYOVERTEMPERATURE PROTECTIONLOGICAL "0" INPUT VOLTAGE UP TO 1.5 V(HIGH NOISE IMMUNITY)INTERNAL CLAMP DIODESThe Device is a mnolithic integrated high voltage,high current four...
This driver uses Infineon chips BTS7960 composed of high-power drive full H-bridge driver module with thermal over-current protection. Double BTS7960 H-bridge driver circuit, with a strong drive and braking, effectively isolating the microcontroller and motor driver! High-current 43Amposed of high-power drive full H-bridge driver module with thermal...
Brand new and high qualityameter: 28mmStep angle: 5.625 x 1 / 64Reduction ratio: 1 / 645 Line 4 phase can be driven by ordinary uln2003 chip can also be connected in phase 2development board used for.supporting the use of a direct plug and easy to use stepper motor used in the development board.Stepper motor driver board with ULN2003A, B, C, D four-phase...
Specification:tor driver, compatible with anything that can output a digital 0 to 5V pulse (or 0 to 3.3V pulse if you solder SJ2 closed on the EasyDriver). EasyDriver requires a 7V to 30V supply to power the motor and can power any voltage of stepper motor. The EasyDriver has an on board voltage regulator for the digital interface that can be set to 5V or...
Features: we quickly realized what an excellent add-on this would be. Using only two pins, control 16 free-running PWM outputs! I2C input, control 16 PWM output, you can control the 16 way servo motor.Specifications:Frequency: 40-1000Hz.Channel number: 16 channel.Resolution: 12 bit.Voltage: DC 5-10VSize: 60*25mmColor: blueNet Weight: 12 gPackage...
HomeerChipsMRF150 RF/VHF/UHF Transistor MOTOROLA(M/A-COM) CASE 211-11 M103MRF150 RF/VHF/UHF Transistor MOTOROLA(M/A-COM) CASE 211-11 M103Package Included:1PCS MRF150 RF/VHF/UHF Transistor MOTOROLA(M/A-COM) CASE 211-11 M103 MRF150 RF/VHF/UHF Transistor MOTOROLA(M/A-COM) CASE 211-11 M103
L298N as main chip, ST corporation production.ion.ion.Low heat,outstanding anti-interference performance.High working power to 46v,large current can reach 3A MAX and continue current is 2A, power to 25w. Can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors.Built-in 78M05,get power from drive power,however, when drive power...
This module is blue PCB now,please know it . . .The DRV8825 stepper motor driver carrier is a breakout board for TI's DRV8825 microstepping bipolar stepper motor driver. The module has a pinout and interface that are nearly identical to those of our A4988 stepper motor driver board, so it can be used as a higher-performance drop-in replacement for those...
L298N as main chip, ST corporation production.ion.ion.Low heat,outstanding anti-interference performance.High working power to 46v,large current can reach 3A MAX and continue current is 2A, power to 25w. Can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors.Built-in 78M05,get power from drive power,however, when drive power...
1.Support the motor voltage 9V to 24V, maximum continuous load current 10A (for 30 seconds), 7.5A (a long time), 10A fuseimum continuous load current 10A (for 30 seconds), 7.5A (a long time), 10A fuseimum continuous load current 10A (for 30 seconds), 7.5A (a long time), 10A fuse2. Support the potentiometer, 0 to 5V analog signal with TTL level,-5V ~ 5V...
SC8UU SCS8UU 8mm Linear Motion Ball Bearing Machinery Slide Bushing CNCDescription:100% brand new and high qualityAluminum ball bearing box sliding unit with sealed ball bearings, easy to install by bolt on a working platform, and to move through the design of compact Aluminum, SBR, TBR series linear guide side railalternatives, low cost, for...
RAMPS 1.4 Controller Board 5PCS DRV8825 StepStick Driver Module For 3D PrinterThe RAMPS 1.4 board is designed to fit the entire electronics needed for a RepRap in one small package for low cost. RAMPS interfaces an Arduino Mega with the powerful Arduino MEGA platform and has plenty room for expansion. The modular design includes plug in stepper drivers...
5V L9110 Fan Motor Module Fan Propeller Firefighting Robot For Arduino DIYDescription:100% brand new and high qualityL9110 drive, speed control with ZhuanPei mounting holes, screw compatible steering gear steering wheel control high quality, high efficiency.Can easily blow out 20 cm away lighter flame can be used for fire fighting robots, robot for...
A4988/DRV8825 3D Printer Stepper Motor Driver Control Extension Shield Boards 1.If jumper is hit the position of ON DP,that means 16 segment (4988) or 32 segment (8825) Jm connected motor2.Jv connect 5v and 12v-24v power supply3.Jc E, S, D, G, respectively corresponding to the connectionof the Enable/Step/Dir/Gnd drive signal output Notice:Pay attention...
RTD PT100 Temperature Sensors Transmitter 0 to 200° DC 24V BlueDescriptionNote: The color of the item may vary slightly due to photography and your own computerThrough the transmitter, resistance signal of the thermal resistance can convert into 4-20mA current signal, convenient to use with computer. Features:Sensor: Pt100Measuring rang: 0 to...
5.8GHZ Microwave Radar Sensor 6-9M Smart Switch for Home Control 3.3-20V DCDescription: It uses Doppler radar technology, with auto-sensing capabilities to control other product,High sensitivity, sensor distance, reliability, wide angle sensor,Wide supply voltage range and other characteristics. Widely used in lighting situations,anti-theft alarm...
50Pcs USB2.0 Type-A Plug 4-pin Male Adapter Connector jack&Black Plastic Cover Product description:Connector Type: USB Type A Male Cable color: Black Package Included: 50 x USB2.0 Type-A Plug 4-pin Male Adapter Connector jac
Stepper motor Pulse Signal Generator/driver controller/Speed Regulator ModuleDescription:100% brand new and high qualityMaterial: Electrical componentsColor: See picturesDescriptionThis is pulse module, can provide 2.5 khz-68 kHz frequency, power signal for stepper driver.If you want to control the stepper motor, you should still use a motor...
Optocoupler Isolation Voltage Test Board 8 Channel AC 220V MCU TTL for PLCFeature: Functuon: Test whether AC 220V is existedOuput TTL Level: can use MCU to test,voltage is 3-5VOutput can connect PLC 24V Wiring: When connecting the PLC input, the PLC's COM terminal is connected to the 24V power supply, the input is connected to signal outputs S1-S8 of the...
HomeerChipsStepper Motor Drive Module L298N Dual H Bridge DC 28BYJ-48 12V Stepper Motor DCFeatures:1.Using L298N made by ST company as the control chip,the module has such characteristics as strong drivingability,low calorific value and strong anti-interference ability.2.This module can use built-in 78M05 for electric work via a driving power supply...
10PCS 1.5A Mini Dual Channel DC Motor Driver Module L298N PWM Speed ControlDescription:motor drive module is ideal for use in battery-powered smart car, toy cars, robots. Supply voltage 2V ~ 10V, can drive two DC motors or a 4-wire 2-phase stepper motors ,can achieve forward rotation or reverse rotation, it is possible to adjust the rotation speed. Each...
2PCS 688-2RS 688 RS Rubber Sealed Ball Bearing Miniature Bearings 8x16x5mmDescription: 8x16x5mm Rubber Sealed Ball Bearing Miniature BearingType:688-2RSSize:(ID)8mm x (OD)16mm x (thickness)5mmPackage Included : 2pcs 688-2RS 688 RS 8x16x5mm Rubb
HomeCategory 1Category 2About Us20db L293D L293 Push-Pull Four-Channel Motor Driver IC DIP-16 NEW L293 Push-Pull Four-Channel Motor Driver IC DIP-16 NEW L293 Push-Pull Four-Channel Motor Driver IC DIP-16 NEWPart No:L293DPin No: 16 pinsPackage Included:20 x L293D L293 Push-Pull Four-Channel Motor Driver IC DIP-16 NEW20db L293D L293 Push-Pull Four-Channel...
2PCS 24V AD16-22SM 22mm Red LED Flash Alarm Indicator Light Lamp with BuzzerrProduct Name: buzzer alarmProduct Type: AD16-22SMProduct Specifications: 28 * 64mmVoltage:24VPerformance parameters1. Power frequency withstand voltage: 2.5KW AC, 1min2. Insulation resistance: more than 2 megohms3. Comparative Tracking Index: CTI greater than or equal to 1004....
3V-36V Dual 15A H-Bridge DC Motor Driver 30A for Robot / Car Arduino CompatibleDescription: The drive performance of these non-L298 motor driver chip can be compared, the driver focus on current and efficiency, effectively motor power and battery life. Can withstand high current overload, the maximum current up to 30A.This drive also has a brake function...
2PCS DRV8825 stepper motor driver Module 3D printer RAMPS1.4 RepRap StepStickThis module is blue PCB now,please know it .The DRV8825 stepper motor driver carrier is a breakout board for TI's DRV8825 microstepping bipolar stepper motor driver. The module has a pinout and interface that are nearly identical to those of our A4988 stepper motor driver board,...
HomeCategory 1Category 2About Us2db StepStick Stepper motor driver A4988 3D Printer driver module Reprap Prusick Stepper motor driver A4988 3D Printer driver module Reprap Prusick Stepper motor driver A4988 3D Printer driver module Reprap PrusThe use chip: original A4988 chipBrief introductionA4988 is a complete microstepping motor driver with built-in...
3 Axis CNC Stepper Motor Driver Controller Board 3.5A TB6560Specification:Toshiba TB6560AHQ chip - High power, maximum 3.5A drive current .Professional design, two-stage signal processing, super anti-jamming.1-1/16 microstep setting - Higher accuracy .Adjustable drive current settings for each axis - 25% ,50% ,75% ,100% of full...
2PCS PAM8302 2.5W Class D Single Channel Audio Amplifier Board Amp ModuleDescriptions:This super small mono amplifier is able to deliver up to 2.5 Watts into 4-8 ohm impedance speakers. Inside the miniature chip is a class D controller, able to run from 2.0V-5.5VDC. It has built in thermal and over-current protection but we could barely tell it got hot....